Showing results: 121 - 135 of 289 items found.
-
Maxim Integrated
Transceivers implement physical layer protocols for various communications and serial bus interface standards. Maxim’s transceivers integrate a wide array of features to increase reliability and simplify designs while providing the highest levels of protection on the market. Click on the following links for more information about each of our transceiver product lines.
-
AR2 -
North Atlantic Industries
The AR2 module provides an ARINC 568/579 communications interface with 2 channels. Channel 1 is Rx and Tx for ARINC 568 and channel 2 is programmable as either Rx or Tx for ARINC 579. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer.
-
Elmeasure India Pvt. Ltd
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
PCI360 -
AcQ Inducom
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
OP-FW10 -
LINEEYE Co., Ltd.
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
uMACC -
Excalibur Systems, Inc.
The uMACC is a wholly contained Communications Converter (data converter - protocol converter or translator). Its small size makes it a complete solution for developing & testing both in the lab and in the field.The uMACC can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to Analog
-
SI-60F -
LINEEYE Co., Ltd.
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
GDU -
Square Peg Communications Inc.
Square Peg Communications Inc.’s Aeronautical Ground Data Unit (GDU) is a software application that runs on the generic Physical Layer Tester (PLT) platform. The GDU supports the testing of physical layer performance and protocol operation for Ground Earth Stations (GESs) and Aeronautical Earth Stations (AESs) implementing Inmarsat Aero services.
-
Bluetooth Tracker -
Ellisys Sàrl
The pocket-sized, bus-powered Bluetooth Tracker designed to support concurrent capture and analysis of Bluetooth Low Energy and Wi-Fi communications, as well as a wide variety of wired interfaces, including logic signals, host controller interface (HCI) protocols (UART and SPI), Audio I2S, and WCI-2, all visualized over the widely adopted Ellisys software suite.
-
79G5P -
North Atlantic Industries
The 79G5P-TE2C0 is a full-height, half-length, PCIe board fitted & configured with the NAI TE2 function module. The TE2 is a single-channel, tri-redundant, Ethernet communications interface module that supports three traffic classes: Time-Triggered Ethernet SAE AS6802 (TTEthernet™), ARINC 664 Part 7 and Avionics Full-Duplex Switched Ethernet (AFDX®) and IEEE 802.3 protocol.
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic Wireless Connectivity solutions encompass a wide range of technologies, with a focus on helping design engineers increase their product's speed-to-market. The Panasonic product portfolio covers all of today's latest communication protocols with ready-to-use modules for Bluetooth BR/EDR, Bluetooth dual mode functionality, Bluetooth low energy functionality and Wi-Fi. Designed with simplicity in mind, Panasonic Wireless Connectivity solutions allow design engineers to quickly extend wireless communication into their feature set without a comprehensive knowledge base of wireless hardware and software design.
-
Vanguard -
Ellisys Sàrl
The most advanced, most comprehensive Bluetooth protocol analyzer ever made. Building on a legacy of innovation, the Bluetooth Vanguard All-In-One Protocol Analysis System delivers new advances designed to ease the increasingly complex tasks of Bluetooth developers. Vanguard provides synchronized capture and analysis of BR/EDR, Bluetooth Low Energy, Wi-Fi 802.11 a/b/g/n/ac (3x3), WPAN 802.15.4 (all 16 2.4 GHz channels), raw 2.4 GHz RF spectrum analysis, HCI (USB, UART, SPI), generic SPI/UART/I2C/SWD communications, WCI-2, logic signals, and Audio I2S.
-
E6966B -
Keysight Technologies
Wireless telephony networks are increasing capacity for high throughput Internet Protocol (IP) packed-data by utilizing radio access technologies such as LTE and HSPA. Session Initiation Protocol (SIP) and IP Multimedia Subsystem (IMS) are progressively being adopted as part of the network infrastructure to carry traditional wireless telephony services over an all-IP network. SIP provides control of communication sessions whilst IMS is the framework that allows delivery of multimedia services over IP. With this new capability comes the need for developers and operators to move their focus to testing user equipment (UE) in this new network environment.
-
HR-E -
Badger Meter
The High Resolution 8-dial Encoder (HR-E) from Badger Meter uses a non-contact field-proven light emitting diode technology to provide a high resolution 8-digit reading while at the same time eliminating friction and wear of traditional mechanical encoders. The HR-E communicates using the industry standard ASCII communication protocol to provide high resolution encoded output.
-
W-IE-NE-R, Plein & Baus GmbH
VXI – (VME eXtension for Instrumentation): The demand for a compact, both flexible and fast industry-standard instrument-on-a-card architecture has driven the development of the VXI standard. The modular form factor, high bandwidth, and commercial success of the VMEbus made it particularly attractive as an instrumentation platform. The tremendous popularity of GPIB also made it attractive as a model for device communication and instrument control protocols.
